Bridge from Solana to Ethereum
Move USDC, SOL, ETH from Solana to Ethereum at the best available rate.
Typical time — Usually well under a few minutes on liquidity-based routes — often somewhere from about half a minute to a couple of minutes — though Ethereum's roughly 13-minute practical finality can mean a short wait before the funds are fully settled..
Quotes include a 0.5% service fee that supports Bridgeline. Swaps execute through LI.FI’s audited smart contracts — this site never holds your funds.
Four steps, all signed in your own wallet.
- 01
Connect your wallet
Connect inside the bridge box. That's the only place Bridgeline ever asks — this site never sees your keys.
- 02
Pick your token and amount
Choose what you're moving, from which chain to which chain, and how much.
- 03
Review the quote and fee
You approve the exact amount in your own wallet, with the full fee shown. Cancel any time before you sign.
- 04
Confirm and track
Sign the transaction and watch it settle on-chain through LI.FI's audited contracts. Bridgeline is never in the middle.
Bridging Solana to Ethereum
Ethereum's mainnet is where the deepest liquidity, the widest set of stablecoins, and the blue-chip DeFi protocols live, so moving over from Solana opens up options that the SVM side simply can't match yet. You'll settle gas in ETH once you land, which typically runs from around a dollar to well over $20 when the network is busy, with blocks arriving roughly every 12 seconds and practical finality closer to 13 minutes. Note that Ethereum uses 0x-style addresses rather than Solana's format, so double-check the destination before you send.
Solana is built for speed and low cost — slots land in roughly 0.4 seconds and fees are typically fractions of a cent — but a large share of the deepest stablecoin pools and blue-chip DeFi still lives on Ethereum mainnet. People usually make this specific move to reach that liquidity: a lending market, an established protocol, or a token whose serious market only exists on L1. Others are consolidating onto Ethereum because the custody options and tooling around it tend to feel more settled to them. The honest trade-off is cost, since Ethereum gas is generally the highest of any chain in this set and a single swap there can run from around a dollar to well over $20 when the network is congested. Because of that, it often makes sense to bridge an amount that justifies the destination fees rather than moving dust.
Solana
Source- Gas
- Fees are fractions of a cent.
- Speed
- About 0.4-second slots; fast confirmation.
- Ecosystem
- A high-throughput non-EVM chain; Jupiter aggregates liquidity. You need a little SOL on arrival to cover fees and account rent.
Ethereum
Destination- Gas
- Swap gas is the highest here — often a few dollars, and more when the network is busy.
- Speed
- About 12-second blocks; practical finality in roughly 13 minutes.
- Ecosystem
- The main settlement layer: deepest liquidity, most stablecoins, and the blue-chip DeFi protocols.
Stay safe while bridging
- Approve only what you’re bridging. The widget requests finite token approvals by default — there’s no need to grant an unlimited allowance.
- Check the URL every time. Bookmark this site and confirm the address bar before connecting a wallet.
- Start small for a new route. A tiny test transfer confirms everything works before you move the full amount.
Moving a large amount? Consider a hardware wallet
A hardware wallet keeps your private keys offline, so a compromised browser or a malicious approval can’t drain your funds on its own. It’s the single biggest security upgrade for anyone holding meaningful value on-chain.
Official links, provided for your security.
Questions about Solana → Ethereum
I have USDC or SOL on Solana — can I use it directly in Ethereum DeFi once it arrives?
It depends on the asset. USDC is issued natively on both Solana and Ethereum, so a good route typically delivers native Ethereum USDC that L1 protocols recognize directly. SOL is a different story: it isn't a native Ethereum asset, so bridging it usually means either receiving a wrapped representation or, more commonly, the route swaps it into an Ethereum-native asset like ETH or USDC along the way. Before you rely on the output in a protocol, check what token standard actually lands in your wallet, because a wrapped version and its native counterpart aren't always interchangeable.
Once my funds reach Ethereum, will I have anything to pay gas with?
You need ETH on Ethereum to pay gas, the same way you needed a little SOL to transact on Solana. If you bridge only USDC across, you can arrive with a balance you can't move because there's no ETH in the wallet to cover the transaction. It's worth either choosing a route that leaves you with a small amount of ETH or keeping some ETH on hand before you start.
Why does this cost noticeably more than moving around on Solana did?
On Solana you were paying fractions of a cent per action, so the jump can feel jarring. Ethereum gas is generally the steepest in this set, and depending on network load a swap can range from roughly a dollar to more than $20. The bridge fee itself is usually modest; the destination-side gas is what tends to dominate, which is why sizing the transfer to something worth those fees matters here.
How long should the Solana-to-Ethereum transfer take?
On liquidity-based routes it's usually well under a few minutes as of publication. The Solana side confirms very quickly given its sub-second slots, and the wait is mostly on the Ethereum end, where blocks come about every 12 seconds and practical finality sits around 13 minutes. It's normal to see the funds show up and then take a little longer to be fully settled.
The Ethereum address looks nothing like my Solana one — did I set this up wrong?
That difference is expected. Solana addresses use a different format entirely, while Ethereum destinations are the familiar 0x-style addresses, so your receiving address will look unlike the one your funds are leaving from. Paste the 0x address of the wallet you actually control on Ethereum, and confirm it character-by-character before bridging, since a transfer sent to the wrong format or wrong chain generally can't be reversed.
Should I leave anything behind on Solana?
If you plan to keep using that Solana wallet, it's worth leaving a small amount of SOL there rather than sweeping it to zero, since SOL covers both transaction fees and account rent on that side. Bridging every last lamport can leave you unable to sign the next action from that wallet. Keeping a little SOL in reserve saves you from having to fund it again later just to move things around.